Do not use to clean any other internal components. Note: The damp cloth should only be used to clean the tipping buckets. Use a damp cloth to clean off the rain gauge tipping buckets.An old toothbrush can help to clean out the hard-to-reach places. After your sensor has been opened, remove any insects, cobwebs, or debris.The screws toward the center of the sensor are for Rain Gauge calibration only. Open your AcuRite Iris™ (5-in-1) outdoor sensor by removing the (4) four screws from the bottom.Please follow the steps below to correct.
Confirm the display is showing 4 full bars of signal strength.Ī -40°/158° outdoor temperature reading or a 1%/99% outdoor humidity reading is an error code reported from the outdoor sensor and is typically caused by corrosion.Make sure the AcuRite Iris™ (5-in-1) sensor is mounted at least 5 feet off of the ground.Make sure both the display unit and AcuRite Iris™ (5-in-1) sensor are positioned away from moisture sources.Make sure both the display unit and AcuRite Iris™ (5-in-1) sensor are placed away from any heat sources or vents.If the temperature or humidity is inaccurate, please confirm the following: These steps may also be performed if you are seeing the following error codes: If the correct region isn’t selected, then your temperature displays will be inaccurate.If your AcuRite Iris™ (5-in-1) Display unit or My AcuRite® account is showing the incorrect or inaccurate outdoor temperature or outdoor humidity readings from your AcuRite Iris™ (5-in-1) Weather Station, please review the troubleshooting suggestions below. Once it is reset, press the GEO button to select the correct region that you’re in. Press and release this button to factory reset the weather station. If you’ve tried everything else on this list but your Acurite Weather Station is still giving you issues, then resetting it might help.įirst, locate the reset button inside the battery compartment of the display unit. When you see a solid sensor signal on the display unit, you’re all set. Keep the units close to one another for about five minutes. As soon as it’s in, press and hold the reset button for 20 seconds. Plug the power cord back into the display unit. If the red light is blinking once every 18 seconds or so, you’re good to go. Then, place the units next to one another.Ĭhange the A-B-C switch to a new letter on both units. Turn off both units and take out the batteries and power cord. If you’re having this issue, you might not have synced them correctly or you may need to re-sync them. Sometimes issues can be caused by the sensor and the display unit falling out of sync. Go to clock hour/clock minute, and set the correct time using the arrow buttons. Press the gear button and then select set mode. If the timezone is correct, but the display time is still wrong, you’ll need to manually set the time. Make sure you’re in the correct time zone. On the back of the unit, there is a button to select your time zone preference. Make sure it’s displaying the correct time.
If your time is displaying incorrectly, it can create a whole host of problems.
How to Set Time on Acurite Weather Station Take off the rain gauge stabilizer once your sensor is mounted. This way, you’ll get the most accurate rain reporting possible. The front solar cell should also face towards the equator (which is South if you’re in the Northern Hemisphere). If your temperature and rain readings are off, ensure your weather station is mounted.įind somewhere that is at least 5 feet off the ground and away from heat and humidity (such as direct sunlight). Place four AA batteries into the 5-in-1 outdoor sensor battery compartment.
Once you’ve chosen your settings, install the sensor batteries. Use the arrows to change between options, and the gear button to select the setting you want. The device will automatically begin the configuration process. If your weather station is displaying incorrectly or giving you other issues, make sure it’s set up correctly.įirst, plug the power cable into your weather station. The Steps for Acurite Weather Station Troubleshooting How to Set Up Acurite Weather Station In this guide, we’ll show you the steps for Acurite weather station troubleshooting so you can get your machine back up and running. Just because your weather station is giving you some grief doesn’t mean it’s down for the count. But, like any technology, their weather stations can sometimes malfunction or even break. Acurite provides excellent weather station solutions for home use.